Understanding Wi-Fi Signals: Why Your Router's Position Matters More Than Its Price
People spend a lot of money replacing routers to fix bad Wi-Fi. In most homes the router was never the problem — it was in the wrong place. Moving it four feet can do more than spending four hundred dollars.
Wi-Fi is a radio, and radios obey physics
Your router transmits at a fixed power level (usually around 100 mW, limited by regulation). That signal spreads out and weakens with distance. Every wall it passes through costs something: drywall loses a few dB, brick loses more, and anything containing water or metal — a fish tank, a mirror, a fridge, a plaster wall with foil-backed insulation — can block the signal almost entirely.
The practical consequence: signal strength falls roughly with the square of distance, and every obstacle adds loss on top. Doubling the distance does not halve the signal, it quarters it.
The five placement mistakes
1. Inside a cupboard or media cabinet
A wooden cabinet costs 5–15 dB, which is the difference between "full bars" and "one bar" at the far end of the house. Metal cabinets are worse — they act as a shield.
2. On the floor, or behind the TV
Wi-Fi radiates outward and slightly downward from most antennas. A router on the floor sends half its energy into the ground. Behind a TV, the TV's own metal chassis blocks the signal in whichever direction the TV faces.
3. Next to the microwave
Microwaves operate at 2.4 GHz — the same band as one of your Wi-Fi channels. While running, they can wipe out 2.4 GHz reception within several metres. If your Wi-Fi drops whenever someone heats lunch, this is why.
4. At the far corner of the house
Routers radiate in all directions, so putting one in a corner wastes half its coverage outside the building. The centre of the living space is almost always better.
5. Right next to other electronics
Baby monitors, cordless phones, Bluetooth speakers and cheap LED drivers all emit in the 2.4 GHz band. Keep at least a metre of distance.
What to do instead
- Put it high and central. Waist-to-head height, in the middle of the area you want covered, with clear line of sight to as many rooms as possible.
- Stand it upright. Most routers have internal antennas arranged vertically; laying the router flat changes the radiation pattern in ways you do not want.
- Aim antennas sensibly. If the router has external antennas, vertical is correct for a single-floor home. For a multi-floor home, angle one antenna horizontally — the radiation pattern is doughnut-shaped around the antenna axis, so a horizontal antenna covers the floor above better.
- Use 5 GHz where you can. It has less range but far more capacity and much less interference. Modern routers steer devices automatically; if yours does not, name the two bands differently and connect fixed devices to 5 GHz.
How to measure the difference
Signal strength is reported in dBm, and it is always negative. Closer to zero is better.
- −30 to −50 dBm: excellent, you are near the router
- −50 to −60 dBm: good, full speed
- −60 to −70 dBm: usable, some speed loss
- −70 to −80 dBm: unreliable, video will stutter
- below −80 dBm: effectively no connection
On Windows, netsh wlan show interfaces prints the current signal as a percentage; a value below 50% corresponds roughly to −70 dBm. On Android, Wi-Fi Analyzer apps show dBm directly. On iOS, the Field Test mode (*3001#12345#*) shows it under "Serving Cell Measurements".
Walk around the house with one of these open, note the worst spots, then move the router and measure again. Ten minutes of this tells you more than any review site.
When moving it is not enough
If the house is large or has thick masonry walls, no single router will cover it. The correct fix is a mesh system with nodes wired together by Ethernet if possible — a wired backhaul keeps full speed at every node. Powerline adapters work as a fallback; Wi-Fi repeaters halve throughput and should be a last resort.